Multifunctional evaporation concentrator detailed features: 1. The whole heating system has the main features of high heat transfer efficiency and short heating time due to uniform steam heating and liquid-liquid flow evaporation. If the heat pump is configured, it has more advantages such as energy saving, low steam consumption and low cooling water circulation. 2. Concentrated liquid material: This equipment adopts the combination of external heating natural circulation and vacuum negative pressure evaporation. The evaporation speed is fast, the concentration ratio can reach 1.3, the liquid material is in the fully sealed state without foam concentration, and the medicine concentrated by this equipment The liquid has the characteristics of no pollution, strong medicinal taste, and convenient cleaning (opening the upper and lower covers of the heater to clean). 3. The material is accelerated downward along the inner wall of the tube to evaporate and evaporate, and the material is more suitable for evaporation and concentration. 4. Since the material evaporates in a film form in each tube, the heating time of the liquid is very short, so it is very advantageous for the evaporation and concentration of the food, and the nutrient content of the food is preserved. 5. The units are all made of SUS304316 stainless steel, which meets the requirements of pharmaceutical GMP and food HACCP. 6. Under the action of vacuum, the evaporation process not only ensures the hygienic requirements of the materials, but also ensures the environmental protection requirements, and greatly reduces the evaporation temperature. In addition, the hot-pressure pump is configured, and some of the secondary steam is re-inhaled and regenerated by the hot-pressure pump. The steam mixing saves the raw steam, and at the same time, since the steam passing through the hot press pump enters the heating casing in the form of a spray mist, the steam rapidly diffuses and the liquid is heated gently, so it is suitable for concentration of the heat sensitive material. 7. Concentration ratio is large, falling film evaporation, so that the viscosity of the liquid is easy to flow and evaporate, the concentration time is short. 8. It is suitable for evaporation and concentration of foaming materials. Because the liquid liquid evaporates in the heating tube, it forms vapor-liquid separation. At the bottom of the effect body, most of the liquid is pumped away, only a small part of the liquid Intensified separation with all secondary steam entering the separator, the liquid solidification process does not form too much impact, avoiding the formation of foam. 9. The equipment is reasonable, compact, small and beautiful in appearance, meets the requirements of use under laboratory conditions, and is easy to operate and maintain; 10. The equipment can be equipped with CIP cleaning system to achieve on-site cleaning. The whole set of equipment is easy to operate and has no dead angle. 11. The equipment continuously feeds in and out. 12. The falling film concentration evaporator produced by our company can be equipped with automatic system to realize automatic feeding control, automatic heating temperature control, automatic discharge concentration control, automatic cleaning control, and can be equipped with sudden power failure and sensitive to faults. Protective measures for sexual materials. Other safety, alarm and other automated operations and controls. Operation and operation of the multifunctional evaporation concentrator : First, first open the vacuum system, open the vacuum valve, the valve is closed, so that the evaporation chamber vacuum reaches 0.08MPa stability, open the feed valve, so that the evaporation chamber liquid will enter the lower part of the steam pipe nozzle 150-200mm ; close the feed valve. Open the steam valve and open the steam condensate out of the water and trap. Start heating and evaporation while opening the cooling water valve. The temperature of the cooling water does not reach the cooling water temperature of the equipment. If it is equipped with a cooling tower system, it is prepared by the user. (The cooling tower is shaped according to the equipment specifications every hour; the condensed water is cooled after evaporating vapor, the drainage pump is started, and the self-flow is discharged. The condensed water is periodically discharged to the pool used by the user. 2. After the operation is normal, continuously feed the evaporating liquid, maintain the original liquid level, collect the paste when the concentrated specific gravity is reached, and after sampling and detecting the anti-required concentration, start the discharge pump. Note: If foam is generated in the evaporation chamber, open the vacuum valve to remove the bubble. Multi-function single-effect concentrator cleaning program: Wash with water (condensed water) for 10-15 minutes, and wash with about 2% with 2% nitric acid solution (HX03). If necessary, open the top and bottom of the evaporator for mechanical cleaning. The top has a CIP cleaner. Maintenance and maintenance of multi-function single-effect concentrator : 1. After the work is completed every day, the multi-function single-effect concentrator should be cleaned. When cleaning, the nature of the liquid can be used to clean the inside of the equipment with different detergents. 2, open the manhole, clean the inner wall of the pot, the corner of the heating coil should be cleaned with wire brush to remove dirt, discharge pipe, cock to be removed and cleaned, all washed with water two or three times. 3. After cleaning, seal the joints, and install the parts in order to use them next time (the plug housing and the core should be installed in pairs, no mistakes can be made to prevent leakage). 4. For the instrument installed on the multi-function single-effect concentrator, it must be protected, not arbitrarily damaged, and often check its sensitivity and error. If damage or error is found, it should be replaced and adjusted in time. 5. The safety valve should be adjusted to a large use steam pressure at a time to ensure normal production and prevent malfunction. 6. The joints of the flanges and joints should be inspected frequently to make them seal well. If the gasket is damaged, it should be replaced immediately. Flood Light Camera,Cctv Flood Light Camera,2Mp 3Mp Flood Light Camera,Waterproof Flood Light Camera Shenzhen Zuomi Technology Co., Ltd. , https://www.zuomicamera.com